QRZ Contest Novmber two Pappa Alpha N2PA

F1 CQ1,{CAT1HEX FEFE94E0280001FD}
F2 Exch,{CAT1HEX FEFE94E0280002FD}
F3 TNX,{CAT1HEX FEFE94E0280003FD}


#   RUN Messages
###################
F1 CQ1,{CAT1HEX FEFE94E0280001FD}
F2 Exch,{CAT1HEX FEFE94E0280002FD}
F3 TNX,{CAT1HEX FEFE94E0280003FD}
F4 {MYCALL},{CAT1HEX FEFE94E0280004FD}
# Replace "-" with "!" if you are using voicing of callsigns 
F5 His Call,- 
F6 Spare,-
F7 QRZ?,{CAT1HEX FEFE94E0280007FD}
F8 Agn?,{CAT1HEX FEFE94E0280008FD}
F9 Zone?,{OPERATOR}\Zone query.wav
F10 Spare,- 
F11 Spare,- 
F12 Wipe, {WIPE}



From N1MM pdf...

IC-7300 using address 94 hex
• ◦ This radio can not be used in SO2V mode because Icom did not provide VFO specific polling
commands. Currently they provide Selected and Unselected VFO Frequency & Mode
commands.
◦ Radio control via USB with Icom driver or CI-V interface.
◦ To control the radio via the USB interface with baud rates above 19200, the radio menu
Connectors, CI-V, CI-V USB Port must be set to “Unlink from Remote”. Then set the menu item
below this, CI-V USB Baud Rate, to the baud rate above 19200.
◦ The radio codec is supported. With the Icom drivers the USB cable can be used for radio
control, AFSK RTTY, PSK, recording voice messages on the fly, voice message playback, and
QSO recording.
◦ To record both sides of a CW transmission with the radio codec, enable this option in the Set
Menu: Connectors, ACC/USB AF Beep/Speech….Output = ON. The CW sidetone level
changes the audio level in the recording. If you set the CW sidetone level to zero, the recording
will not contain the transmitted audio.
◦ Detailed instructions for setting up USB communications with these radios may be found under
Supported… Supported Radios
559
> Downloads > Additional Support Files. The file is titled “IcomUSBCodecInstructions.pdf” If you
have questions post a message on the Logger+ reflector.
◦ To play an internal voice (DVK) message, program function key or Bandmap button with the
CatMacro below. Pressing the ESC key will stop a voice message. There is no need to program
a STOP command. These commands work, but they are undocumented for the IC-7300. Thus,
there are no guarantees that they will work. Be sure you are running the latest firmware update.
They were tested with V1.20 of the firmware.
▪ Voice Message1 = {CAT1Hex FE FE 94 E0 28 00 01 FD}
▪ Voice Message2 = {CAT1Hex FE FE 94 E0 28 00 02 FD}
▪ Voice Message3 = {CAT1Hex FE FE 94 E0 28 00 03 FD}
▪ Voice Message4 = {CAT1Hex FE FE 94 E0 28 00 04 FD}
▪ Voice Message5 = {CAT1Hex FE FE 94 E0 28 00 05 FD}
▪ Voice Message6 = {CAT1Hex FE FE 94 E0 28 00 06 FD}
▪ Voice Message7 = {CAT1Hex FE FE 94 E0 28 00 07 FD}
▪ Voice Message8 = {CAT1Hex FE FE 94 E0 28 00 08 FD}
▪ Stop Voice Message = {CAT1Hex FE FE 94 E0 28 00 00 FD} (programmed into the
ESC key)
◦ Note: The CatMacro command can be entered with or without spaces:
▪ {CAT1Hex FE FE 94 E0 28 00 01 FD} or {CAT1Hex FEFE94E0280001FD}
• Digital Mode Mapping for the IC-7300
◦ RTTY = RTTY
◦ RTTY-R = RTTY-R
◦ AFSK = LSB-D
◦ AFSK-R = USB-D
◦ nothing for psk or psk-r